dl5221 thru dl5281 500 mw zener diode 2.4 to 200 volts feat ures wide voltage range available glass package high temp soldering: 250 c for 10 seconds at terminals surface mount package maximum ratings operating temperature: - 5 5 c to + 150 c storage temperature: - 5 5 c to + 15 0 c 500 mwatt dc power dissipation power de rating: 4.0mw/ c above 50 c forward voltage @ 200ma: 1.1 volts figure 2 - derating curve power dissipation (mw) - versus - temperature c temperature c 0 5 0 1 0 0 1 5 0 mw 200 400 typical capacitance (pf) ? versus ? zener voltage (v z ) figure 1 - typical capacitance 0 100 200 1 10 100 pf v z at zero volts at ? 2 volts v r a b c cathode mark 0. 0 3 0 ? 0.1 0 5 0. 0 75? suggested solder pad layout minimelf dimensions inches mm dim min max min max note a .134 .142 3.40 3.60 b .008 .016 .20 .40 c .055 .059 1.40 1.50 ? www. mccsemi .com
om p on ent s 21 20 1 i t a sc a s t ree t ch at s w or th ! " # $
% ! " # mcc
mcc part number nominal zener voltage v z @ i zt test current i zt maximum zener impedance ?b? suffix only z zt @ i zt z zk @i zk = 0.25ma maximum reverse leakage current i r @ v r max. zener vol tage temp coefficient ?b? suffix only volts ma ohms ohms m a volts % / c dl5221 2.4 20 30 1200 100 1.0 - 0.085 dl5222 2.5 20 30 1250 100 1.0 - 0.085 dl5223 2.7 20 30 1300 75 1.0 - 0.080 DL5224 2.8 20 30 1400 75 1.0 - 0.080 dl5225 3.0 20 29 1600 50 1.0 - 0.075 dl5226 3.3 20 28 1600 25 1.0 - 0.070 dl5227 3.6 20 24 1700 15 1.0 - 0.065 dl5228 3.9 20 23 1900 10 1.0 - 0.060 dl5229 4.3 20 22 2000 5.0 1.0 0.055 dl5230 4.7 20 19 1900 5.0 2.0 0.030 dl5231 5.1 20 17 1600 5.0 2.0 0.030 dl5232 5.6 2 0 11 1600 5.0 3.0 +0.038 dl5233 6.0 20 7.0 1600 5.0 3.5 +0.038 dl5234 6.2 20 7.0 1000 5.0 4.0 +0.045 dl5235 6.8 20 5.0 750 3.0 5.0 +0.050 dl5236 7.5 20 6.0 500 3.0 6.0 +0.058 dl5237 8.2 20 8.0 500 3.0 6.5 +0.062 dl5238 8.7 20 8.0 600 3.0 6.5 +0 .065 dl5239 9.1 20 10 600 3.0 7.0 +0.068 dl5240 10 20 17 600 3.0 8.0 +0.075 dl5241 11 20 22 600 2.0 8.4 +0.076 dl5242 12 20 30 600 1.0 9.1 +0.077 dl5243 13 9.5 13 600 0.5 9.9 +0.079 dl5244 14 9.0 15 600 0.1 10 +0.082 dl5245 15 8.5 16 600 0.1 11 +0.082 dl5246 16 7.8 17 600 0.1 12 +0.083 dl5247 17 7.4 19 600 0.1 13 +0.084 dl5248 18 7.0 21 600 0.1 14 +0.085 dl5249 19 6.6 23 600 0.1 14 +0.086 dl5250 20 6.2 25 600 0.1 15 +0.086 dl5251 22 5.6 29 600 0.1 17 +0.087 dl5252 24 5.2 33 600 0 .1 18 +0.088 dl5253 25 5.0 35 600 0.1 19 +0.089 dl5254 27 4.6 41 600 0.1 21 +0.090 dl5255 28 4.5 44 600 0.1 21 +0.091 dl5256 30 4.2 49 600 0.1 23 +0.091 dl5257 33 3.8 58 700 0.1 25 +0.092 dl5258 36 3.4 70 700 0.1 27 +0.093 dl5259 39 3.2 80 80 0 0.1 30 +0.094 dl5260 43 3.0 93 900 0.1 33 +0.095 dl5261 47 2.7 105 1000 0.1 36 +0.095 dl5262 51 2.5 125 1100 0.1 39 +0.096 dl5263 56 2.2 150 1300 0.1 43 +0.096 dl5264 60 2.1 170 1400 0.1 46 +0.097 dl5265 62 2.0 185 1400 0.1 47 +0.097 dl5266 68 1.8 230 1600 0.1 52 +0.097 dl5267 75 1.7 270 1700 0.1 56 +0.098 dl5268 82 1.5 330 2000 0.1 62 +0.098 dl5269 87 1.4 370 2200 0.1 68 +0.099 dl5270 91 1.4 400 2300 0.1 69 +0.099 dl5271 100 1.3 500 2600 0.1 76 +0.110 dl5272 110 1.1 750 3000 0.1 84 +0.110 dl5273 120 1.0 900 4000 0.1 91 +0.110 dl5274 130 0.95 1100 4500 0.1 99 +0.110 dl5275 140 0.90 1300 4500 0.1 106 +0.110 dl5276 150 0.85 1500 5000 0.1 114 +0.110 dl5277 160 0.80 1700 5500 0.1 122 +0.110 dl5278 170 0.74 1900 5500 0.1 12 9 +0.110 dl5279 180 0.68 2200 6000 0.1 137 +0.110 note 1: table as shown lists type numbers, which indicate a tolerance of 20% with guaranteed l imits on only vz, i r , and v f . devices with guaranteed limits o n all six parameters are i ndicated by suffix ?a? for 10%, ?b? for 5%, ?c? for 2%, and ?d? for 1% tolerance note 2: the electrical characteristics are measured after allowing the device to stabilize for 20 seconds. note 3: temperature coeff i cient ( v z ). test conditions for temperature coefficient are as follows: a. i zt = 7.5ma, t i = 25 o c t 2 = 125 o c (dl5221 thru dl5242 ) b. i zt = rated i z t , t i = 25 o c, t 2 = 125 o c (dl5243 thru dl5281 ) device to be temperature stabilized with current applied prior to reading breakdown voltage a t the specified ambient temperature. www. mccsemi .com dl52 80 1 9 0 0. 66 24 00 6 500 0.1 1 44 +0.110 dl52 81 2 00 0.6 5 2 5 00 7 000 0.1 1 52 +0.110 mcc dl 52 21 t hr u dl 52 81
|
